MTCUME – MikroTik Certified User Management Engineer

Module 1- PPP

• PPP Profile
  • Local and remote addresses
  • Incoming and outgoing filters
  • Address list
  • Change TCP-MSS
  • Use encryption
  • Session timeout
  • Rate-limit configuration
  • Only-one setting
• PPP Secret
  • Service and Profile
  • Local and Remote address
  • Routes configuration
  • Limit Bytes In/Limit Bytes Out configuration
• IP Pool
  • Set addresses ranges
  • Next pool options
• Module 1 laboratory

Module 2- PPTP, L2TP

• PPTP and L2TP
  • Theory
  • Comparison
  • PPTP Client configuration
    • Client setup
    • Set profile
    • Dial on demand
    • Add default route and static routes
    • PPTP Server configuration
      • Enable server
      • Setup profiles
      • Add clients to PPP secret
      • Set static interfaces for clients
      • L2TP Client configuration
        • Client setup
        • Configure profile
        • Dial on demand
        • Add default route and static routes
      • L2TP Server configuration
        • Enable server
        • Set profiles
        • Add clients to PPP secret
        • Set Static interfaces for clients
      • Module 2 laboratory

Module 3- PPPoE

• PPPoE server and client
  • Theory
  • Usage environment
  • Comparison to other PPP protocols
  • PPPoE client configuration
    • Client setup
    • Select interface
    • Service name
    • Configure profile
    • PPPoE Server configuration
      • Enable PPPoE server
      • Set profiles
      • Add clients to PPP secret
      • Add Static interfaces for clients
      • Secure server by removing any IP address from PPPoE server interface
      • Encryption
        • Set profile without encryption
        • Set profile with encryption
        • Configure PPPoE client without encryption
      • Interface ECMP
        • Set ECMP routes for PPP interfaces
      • Module 3 laboratory

Module 4- Bridging

• L2TP and EoIP
  • Set L2TP tunnel
  • Set EoIP tunnel
  • Create bridge and add necessary interfaces to ports
  • Confirm you have Ethernet connectivity between remote nodes
  • L2TP and VPLS
    • Set L2TP tunnel
    • Set VPLS tunnel
    • Create bridge and add necessary interfaces to ports
    • L2TP and BCP
      • Set L2TP tunnel
      • Use BCP to bridge PPP interface
      • Add to bridge necessary interface
      • Multilink Protocol
        • Enable multilink by specifying correct MRRU settings
        • Disable mangle rules for MSS adjustment
      • MLPPP (optional)
        • Setup client and specify multiple interfaces for one client
        • Set PPPoE server with MLPPP support
      • Module 4 laboratory

Module 5- HotSpot

• Introduction
  • Concepts
  • Usage environments
  • Setup HotSpot with default settings
• HotSpot Login Methods
  • HTTP CHAP/PAP
  • MAC
  • Cookie
  • HTTPS
  • Trial
  • RADIUS
• Users
  • Add users
  • Set MAC-address for user
  • Set MAC-address for username
  • Limit Uptime and Limit Bytes In/Out
  • Reset limits for user
• Monitor Users
  • Host Table
  • Active Table
  • SNMP for users
• Profile
  • Keepalive timeout
  • Shared users
  • Rate-Limit
  • Address-list
  • Incoming/Outgoing filter
  • Incoming/Outgoing Packet Mark
• Bypass HotSpot
  • Walled garden
  • Walled garden IP
  • IP binding
• Customize HotSpot
  • Advertisement
  • Customize pages
• Module 5 laboratory

Module 6- RADIUS

• RADIUS client
  • Add radius client
  • Set service
  • Use RADIUS for the specific service
• RADIUS server
• User manager
  • Install the latest user-manager
  • Add routers
  • Add users
  • Set profile
• RADIUS incoming
• Module 6 laboratory